WWW.DUMAIS.IO

ARTICLES

OVERLAY NETWORKS WITH MY SDN CONTROLLER SIMPLE LEARNING SWITCH WITH OPENFLOW INSTALLING KUBERNETES MANUALLY WRITING A HYPERVISOR WITH INTEL VT-X CREATING YOUR OWN LINUX CONTAINERS VIRTIO DRIVER IMPLEMENTATION NETWORKING IN MY OS ESP8266 BASED IRRIGATION CONTROLLER LED STRIP CONTROLLER USING ESP8266.OPENVSWITCH ON SLACKWARE SHA256 ASSEMBLY IMPLEMENTATION PROCESS CONTEXT ID AND THE TLB THREAD MANAGEMENT IN MY HOBBY OS ENABLING MULTI-PROCESSORS IN MY HOBBY OS NEW HOME AUTOMATION SYSTEM INSTALLING AND USING DOCKER ON SLACKWARE SYSTEM ON A CHIP EMULATOR USING JSSIP AND ASTERISK TO MAKE A WEBPHONE C++ WEBSOCKET SERVER SIP ATTACK BANNING BLOCK CACHING AND WRITEBACK BEAGLEBONE BLACK BARE METAL DEVELOPEMENT ARM BARE METAL DEVELOPMENT USING EPOLL MEMORY PAGING IMPLEMENTING HTTP DIGEST AUTHENTICATION STACK FRAME AND THE RED ZONE (X86_64)AVX/SSE AND CONTEXT SWITCHING HOW TO ANSWER A QUESTION THE SMART WAY.REALTEK 8139 NETWORK CARD DRIVER REST INTERFACE ENGINE CISCO 1760 AS AN FXS GATEWAY HOME AUTOMATION SYSTEM EZFLORA IRRIGATION SYSTEM SUMP PUMP MONITORING BUILDING A HOSTED MAILSERVER SERVICE I AM NOW HOSTING MY OWN DNS AND MAIL SERVERS ON AMAZON EC2 DEPLOYING A LAYER3 SWITCH ON MY NETWORK ACD SERVER WITH RESIPROCATE C++ JSON LIBRARY IMPLEMENTING YOUR OWN MUTEX WITH CMPXCHG WAKEUPCALL SERVER USING RESIPROCATE FFT ON AMD64 CLONING A HARD DRIVE CONFIGURING AND USING KVM-QEMU USING COUCHDB INSTALLING COUCHDB ON SLACKWARE NGW100 MY OS AND EDXS/LSE NGW100 - MY OS ASTERISK FILTER APPLICATION CISCO ROUTER CONFIGURATION AASTRA 411 XML APPLICATION SPA941 PHONEBOOK SPEEDTOUCH 780 DOCUMENTATION AASTRA CONTACT LIST XML APPLICATION AVR32 OS FOR NGW100 ASTERISK SOUND INJECTION APPLICATION NGW100 - DIFFERENT PROBLEMS AND SOLUTIONS AASTRA PRIME RATE XML APPLICATION SPEEDTOUCH 780 CONFIGURATION USING COUCHDB WITH PHP AVR32 ASSEMBLY TIP AP7000 AND NGW100 ARCHITECTURE AASTRA WEATHER XML APPLICATION NGW100 - GETTING STARTED AASTRA ALI XML APPLICATION

CLONING A HARD DRIVE

2012-05-17

Cloning a hard drive

In one of my computers, I have one hard drive that contains 2 partitions: 1 for the root filesystem and one for my /home partition. When I bought a new hard drive, I needed to clone the old one on the new one. This can be easily done with "dd" as long as your partitions are the same size. So I decided to keep the root filesystem with the same size, but wanted to grow the /home partition.

Create the partitions

First, you need to create the partitions on the new drive using fdisk. Remember to keep the same size for the partitions you wanna clone. If you create them smaller, you will end up with a corrupted filesystem. If you create them larger, you will not be able to access the extra space so it will be wasted. After creating the partitions, you don't need to create a filesystem on them (mkfs) since "dd" will clone the partition table of the old hard drive too. But of course, you will need to create a FS for the other partitions that won't be cloned.

Clone

You need to clone your master boot record (which contains lilo/grub). We need to copy the first 512 bytes (the first sector):


dd if=/dev/sda of=/dev/sdb bs=512 count=1

Then, we can clone the partition:


dd if=/dev/sda1 of=/dev/sdb1 bs=4096 conv=noerror

At this point, my root partition was cloned successfully. For the other partition (/dev/sdb2), I had to create a new filesystem (mkfs) because my partition needed to be larger. After that, I copied the files manually using "cp".